TS SMARTER

Transmission System (T.S) Smarter

Transmission Smarter is nothing but a NANO - CERAMIC LIQUID ADDITIVE, the name given by us, is a special product of the Company for the wear recovery of all kinds of mechanical transmission equipment.

Product Efficiency

  • Eliminate the wear of the friction surfaces.
  • Improve the finish of the friction surface.
  • Improve accuracy level.
  • Reduce friction coefficient.
  • Optimize the gaps.
  • Extend the equipment service life.
  • Reduce noise and vibration.
  • Repair the worn surface and to restore the original geometry.
  • Reduce energy consumption.
  • To eliminate scratches and nap traces of machine working surfaces.
  • To reduce the working temperature of the lubricating oil.
  • Reduce noise and vibration.
  • Overhaul-free for the new equipment.
  • Improve abrasion resistance.
  • Improve the working condition of equipment.
  • Reduce equipment working temperature.
  • Extend the maintenance and overhaul period.
COMPRESSOR

The Product optimizes the machine gaps; and reduces vibration; reduces noise; improves abrasion resistance, improves equipment-working condition; and reduces equipment-working temperature.

Application:

Reciprocating, rotary screw and rotary centrifugal air compressors.

  • Optimize the machine gaps.
  • Reduce vibration.
  • Reduce noise.
  • Improve abrasion resistance.
  • Improve equipment working condition.
  • Reduce equipment working temperature.
  • Extend the maintenance period.
  • Extend equipment service life.
  • Save fuel, improve power.
  • Balance cylinder pressure.
  • Reduce harmful gas emissions.

TS Smarter: Add Method for The Compressor

  • Three(3) adding are required.
  • Replaced with new lubricating oil before adding TS Smarter.
  • To Inject TS Smarter into engine oil tankers.
  • Boot device with its normal speed.
  • Second and third adding at intervals of 6-16 hours each.
  • No replacement of new lubricating oil/new grease is required during adding period.

Precautions

Adding T.S Smarter is allowed only after changing used lubricating oil and oil filters.

HYDRAULIC SYSTEM

The Product restores the geometry of the machine worn parts, to less machine wears; and improve working efficiency of the hydraulic pump; eliminates overflow of the hydraulic distributor.

  • Restore the geometry of the machine worn parts, to less machine wears.
  • Improve working efficiency of the hydraulic pump.
  • Eliminate overflow of the hydraulic distributor.
  • Reduce vibration.
  • Improve working pressure and the volumetric efficiency of the hydraulic system.
  • Reduce the channeling of the hydraulic motor.
  • Extend the service life of the hydraulic system up to 2.5 times.

TS Smarter: Add Method in The Hydraulic System

  • Five time addings are required. To shake TS Smarter bottle a few times before adding.
  • To inject TS Smarter into the engine oil tanker of hydraulic system.
  • To maintain same adding method in the second, third, fourth and fifth adding. The time interval between the various stages of 8-16 hours.
  • Every time to add 4ml TS Smarter. Total adding: 20ML TS Smarter.

Precautions

Adding T.S Smarter is allowed only after changing used lubricating oil and oil filters

Note

No replacement of new lubricating oil/new grease is required during adding period.

GEARS

You restore the geometry of the worn surface, to optimize the gear surface, u repair the gears worn surface and contact points u to eliminate working surface scratches and nap trace

  • Restore the geometry of the worn surface, to optimize the gear surface.
  • Repair the gears worn surface and contact points.
  • To eliminate working surface scratches and nap traces.
  • Reduce the working temperature of the lubricating oil.
  • Reduce power consumption up to 25%.
  • Reduce noise and vibration.
  • Extend the gears service life of 2-3 times.
  • You Overhaul free for new equipment once T.S Smarter being used.

T.S Smarter: Add Method for Gears.

  • To shake T.S Smarter bottle a few times before adding.
  • If necessary, turn off the power. To open the gearbox inspection-hole and inject the T.S Smarter directly into the gears work surface, tighten the lid and start the machine with normal operation.
  • If the worn surface area exceeds 10% of gears surface, it needs 2nd time adding. Adding interval is 8-16 hours after 1st time adding with same adding method.
  • After working 400 hours, the device can gradually enter into the new conditions.
  • In case the worn surface exceed 80% of gears surface area, this product is not applicable.

Precautions

Adding T.S Smarter is allowed only after changing used lubricating oil and oil filters.

Remarks

For those machines equip with filtration system and (or) oil-water separation unit and/or for those gear transmission system (hydraulic pumps, hydraulic distributor, hydraulic motor) operate with same lubrication system, it is suggested to add T.S Smarter five time with 4ml TS Smarter per liter of lubricating oil. Adding method is suggested as above.

SLIDING TRACK

The product repairs the worn surface and to restore it to the original geometry and reduce vibration, stabilizes lathe hydraulic system performance; and improve the lathe processing accuracy.

  • Repair the worn surface and to restore it to the original geometry
  • Reduce vibration
  • Stable lathe hydraulic system performance;
  • Improve the lathe processing accuracy;
  • Reduce energy consumption
  • Extend the lathe service life 2-3 times

T.S Smarter: Adding Method in The Sliding Tracks:

  • 1. Three(3) addings are required:
    • To replace with new lubricating oil before adding.
    • To inject TS Smarter into engine oil tankers.
    • Boot device running with its normal speed.
  • 2. Second and third time of TS Smarter injection at intervals of 6-16 hours after first time injection.
  • 3. No replacement of new lubricating oil/new grease is required during adding period.

Precautions

Adding T.S Smarter is allowed only after changing used lubricating oil and oil filters.

BEARINGS

The product eliminates the wear of the friction surfaces; improves the bearing surface finish; improves accuracy level; reduces friction coefficient; optimizes the bearing clearance.

  • Eliminate the wear of the friction surfaces.
  • Improve the bearing surface finish.
  • Improve accuracy level.
  • Reduce friction coefficient.
  • Optimize the bearing clearance and to increase bearing life.
  • Extend bearing service life several times.
  • Reduce the working oil temperature.
  • Reduce noise and vibration.
  • Save energy.

T.S Smarter: Adding Method for The Bearing

  • 1. Three(3) addings are required:
    • To replace with new lubricating oil before adding.
    • To inject TS Smarter into engine oil tankers.
    • Boot device running with its normal speed.
  • 2. Second and third time of TS Smarter injection at intervals of 6-16 hours after first time injection.
  • 3. No replacement of new lubricating oil/new grease is required during adding period.

Precautions

  • The used lubricating oil and used oil filter should be changed into new one before adding T.S Smarter.
  • In case the worn surface exceed 80% of bearing surface area, this product is not applicable.